免烘烤玻璃絲印油墨

品牌：歐萊斯

適用對象：金屬，玻璃，陶瓷，電鍍，五金，不銹鋼，鋁合金，拉絲面板

單件凈重：1公斤

著色力：100

細度：0.01

粘度：1500S

流動度≥：100

保質期：72個月

型號：MPL

用途：1.適用范圍:鐵、鋁、合金、玻璃、陶瓷、電鍍、石材、陽極氧化鋁表面及烤 （噴）漆面等2.稀釋劑:用本公司S-03稀釋劑3.固化劑:可添加TA-9154硬化劑10%增加附著力,提高墨膜硬度。

耐溫性：低溫玻璃油墨

性能：自干玻璃漆

供應玻璃油墨基本信息

本產品是采用高級進口丙烯酸樹脂和高級顏料經過細制研磨加工組合而成，用于各種金屬、玻璃、陶瓷、石材、電鍍(含水電鍍)、陽極氧化鋁表面及烤（噴）漆面等制品的絲印及移印，不需加固化劑，不需烘烤，即可獲得的附著力。

油墨特性：

1、平光、附著力佳、耐汽油、耐化學品；

2、手感好，流平性佳、面光潔；

3、表面硬度好，耐沖擊性能強、抗刮傷；

4、耐汽油、耐酒精、耐化學品程度佳；

印刷：

選用網目為100-350目，以120T網紗計算涂覆蓋面積每公斤達30~35㎡。

表干時間自然揮發5-15分鐘，實干時間在24小時以內，48小時后達較佳性能。

1．用配套專用稀釋劑開油水

2．用718洗網水洗網。

3．或添加配套硬化劑10%可增加附著力,提高墨膜硬度。

4．烤箱80℃烘烤10分鐘佳能更優。

測試方法（完全干燥后）：

1．3M膠紙粘在畫有百格的油墨表面45度角迅速拉起不脫油。

使用方法：

1．建議用我公司專用稀釋劑進行稀釋，不建議使用783慢干稀釋劑稀釋，使用前應充分攪拌，用后隨時密封。

2．攪拌時加本公司配套開油水10-12%，稀釋到印刷適合粘度，移印稀釋使用移印專用稀釋劑；用718洗網水清洗。

3．不得與其它類型油墨混合使用，否則容易出現其他附著力，化學反應等不良現象。

4. 加入固化劑的油墨使用時限為8小時，過期請棄用，剩余油墨不可回收

注意事項：

1．各種承印物料的外觀相似，但可能會是不同的材料，客戶需先試印，確其符合要求后，再批量生產。

2．在移印過程中，如出現拉絲或散開，可適當加入一些慢干膏即可;

3．環境溫度過高，將會影響油墨原有質量。白色超越150都會變色，烘烤時請用木質材料墊底進行烘烤，不得直接接觸鐵

4．根據氣候變化，請遠離火源，陰暗處15度-30度環境下存放。

Brand: oleser

Applicable objects: metal, glass, ceramic, electroplating, hardware, stainless steel, aluminum alloy, drawing panel

Net weight: 1 kg

Tinting power: 100

Fineness: 0.01

Viscosity: 1500S

Flow degree is larger than 100

Shelf life: 72 months

Model: MPL

Purpose: 1. scope: iron, aluminum, alloy, glass, ceramics, stone, electroplating, anodic alumina surface and baked (spray) 2. paint thinner: with the company S-03 diluent 3.: add TA-9154 curing agent hardening agent 10% increased adhesion, improve the ink film hardness.

Temperature resistance: low temperature glass ink

Properties: self drying glass paint

Basic information for glass ink

This product is the use of advanced import acrylic resin and senior pigment after fine grinding system combination, all kinds of metal, glass, ceramic, stone, used for electroplating (aqueous electroplating), anodic alumina surface and baked (spray) and silk screen printing products such as paint, without curing agent, and does not need to bake, can be obtained excellent adhesion.

Ink characteristics:

1, Matt, adhesion, petrol, chemical resistance;

2, feel good, leveling good, smooth surface;

3, surface hardness, impact resistance, scratch resistance;

Print:

The mesh is 100-350 mesh, 120T mesh with coverage area calculation per kilogram of 30~35 square meters.

Table dry time natural evaporation 5-15 minutes, work time in less than 24 hours, 48 hours after the best performance.

1., with a dedicated diluent to open oil and water

2. wash net with 718 washing nets.

3. or add matching hardening agent 10%, increase adhesion, improve ink film hardness.

4. oven 80 degrees baking 10 minutes, Canon is better.

Test method (fully dry):

1.3M tape is glued to the surface of the ink that has a hundred squares, and the 45 degree angle is pulled rapidly without oil removal.

Usage method：

1., I suggest using my company's special diluent for dilution, do not recommend using 783 slow dry diluent dilution, before use should be fully agitated, after use at any time sealed.

2. add the company supporting stirring open water 10-12%, diluted to printing for viscosity, printing the dilution used printing special thinner; use clean water to wash the nets 718.

3., and other types of ink may not be mixed use, otherwise prone to other adhesion, chemical reactions and other undesirable phenomena.

4., the use of curing agent ink, the use of time limit is 8 hours, expired please abandon, and the remaining ink can not be recycled

Matters needing attention：

1., the appearance of a variety of printing materials similar, but may be different materials, customers need to try to print, to ensure that they meet the requirements, and then mass production.

2. in the pad printing process, such as drawing or spreading, you can properly add some slow dry paste can be;

3. environmental temperature is too high, will affect the original quality of ink. White over 150 will change color. When baking, please use wooden material at the bottom of baking, not direct contact with iron

4., according to climate change, please stay away from the fire, dark place, 15 degrees -30 environment storage.

主營行業：化工原料、輔料//玻璃油墨 公司注冊地址：上海 法人代表：趙菁
員工人數：50-100人 廠房面積： 年營業額：人民幣500萬元/年-人民幣1000萬元/年
年進口額：人民幣10萬元/年以下 年出口額：人民幣10萬元/年以下 主要市場：
客戶群：
公司名稱:上海凱賢印刷科技公司
注冊資本:人民幣30萬元/年-人民幣50萬元/年 公司網址：http://AA111213.glass.com.cn

主營產品：pp免處理油墨,PE免處理油墨,金屬油墨,玻璃油墨,陶瓷油墨,uv油墨,abs油墨,亞克力油墨 公司成立年份：2009
公司網址：http://AA111213.glass.com.cn

聯系人：楊洪
電話：-021-59507952-
移動電話：19110524835
傳真：86-021-59507635-
地址：滬宜公路6106號
網址：http://AA111213.glass.com.cn

按加工溫度分